Can You Install an Aluminum Slat Fence Yourself? A DIY Guide
Short answer: yes. If you can measure accurately, set a post plumb and use a drill and a saw, you can install a QuickScreen aluminum slat fence yourself. It’s a friction-fit system with no welding and no visible screws, and it installs about 3x faster than a wood fence. The part that takes the most care is setting the posts; once they’re in, the slats go in quickly.
Doing it yourself also saves the cost of a fence contractor, which typically runs around $15 to $40 per foot for aluminum fencing. This guide covers whether DIY suits your project, the tools you’ll need and the steps in brief, and points you to our full installation guide, videos and technical documents.
Start Here: Our Installation Resources
- How to install guide: our step-by-step installation guide, from measuring your space to choosing your post installation method and attaching posts to a wall.
- Installation videos: watch the 3-Way Fence Assembly and Gate Installation videos, or see all our videos on the Foundation Fence Supply YouTube channel.
- Technical documents: specification sheets for each QuickScreen series (65, 150, Combo and Full Privacy) and the fence and gate wind rating report.
- Fence calculator: enter your fence runs and gates to see exactly which panels, posts, gates and accessories you need.
Is It a Good DIY Project for You?
An aluminum slat fence is a good fit for DIY if:
- You’re comfortable with a tape measure, level and string line
- You can dig post holes and mix concrete, or you’re mounting to an existing slab or wall
- The ground is reasonably flat, or the slope is gentle
- You have a helper for setting posts and hanging gates
It’s worth hiring a contractor for steep or stepped slopes, very long runs, rocky ground or wide driveway gates. You can still buy the materials from us and have any fence contractor install them, or use one of our preferred installers in Texas and Florida.
Tools You’ll Need
- Tape measure, string line, stakes and spray paint
- Post-hole digger or auger, plus concrete mix (for posts set in concrete)
- Drill/driver with masonry bits and anchors (for surface mounting or wall attachment)
- 4-foot level or post level
- Miter or chop saw with a blade rated for aluminum (non-ferrous), for cutting slats to length
- Rubber mallet, clamps, safety glasses and gloves
The Steps, in Brief
These follow our how to install guide, which has the full detail.
1. Measure your space. Measure the total width of the area where your fence and gates will go, then decide how to divide it between fence panels and gates. For example, a 10 ft opening could be one 4 ft gate and one 6 ft fence panel. Put your measurements into the fence calculator and it works out every panel, gate, post and slat you need.
2. Plan your layout. Mark where each gate post, fence post, end post and corner post will go, keeping standard system sizes in mind. Check HOA rules and permits, and in the US call 811 before you dig so buried utility lines get marked. In wildfire areas, check your local code: Colorado now requires noncombustible fencing within 8 feet of homes in WUI areas (see our Colorado guide).
3. Customize if needed. The system is designed for flexibility: slats can be cut to fit narrower openings, posts can be trimmed to achieve custom heights, and panel widths can be adjusted during installation.
4. Mark post locations. Once your layout is final, mark each post location with spray paint, stakes or a string line, and double-check your measurements before installing posts. Accurate post placement is critical for a smooth installation.
5. Choose your post installation method.
- In concrete: recommended for maximum strength, ideal for fence runs and gates, and the most common method.
- Surface mount (base plates): posts mount on concrete slabs or footings; ideal for patios, driveways and retaining walls.
- Wall attachment: blank posts are fixed to a wall through 1-inch access holes and finished with black hole plugs. See attaching a post to a wall and download our illustrated wall-mount guide (PDF).
Keep every post plumb and in line, and let concrete cure before you hang gates.
6. Assemble the fence and hang the gates. Fit the side frames, add the slats with spacers to set your gap, from 3/8″ up to 1″ (or none for full privacy), and finish with the caps. Gate kits include the frames, hinges and a key-locking latch; double gates also include a drop rod. The 3-Way Fence Assembly and Gate Installation videos show both stages.
Tips That Save Time
- Set your first and last posts, then string between them. Every post in between lines up to the string.
- Measure each opening before you cut slats. Cut to the actual opening, not the plan.
- Do the gate posts first and give them extra care. A gate post that’s slightly out of plumb shows up as a gate that sags or won’t latch.
- Keep the cut ends clean. A fine-tooth non-ferrous blade gives a clean edge on aluminum.
- Check the spec sheet for your series. Our technical documents give the dimensions for each QuickScreen series.
Frequently Asked Questions
Can a homeowner install an aluminum slat fence?
Yes. QuickScreen is a friction-fit system designed for DIY, with no welding and no visible screws. The key skill is setting posts accurately; after that, the slats go in quickly. Our how to install guide walks through each step.
Are there installation videos?
Yes. Watch the 3-Way Fence Assembly and Gate Installation videos, which are also on our how to install page.
How do I know what materials to order?
Use the fence calculator. Enter your fence runs and gates and it lists the panels, posts, gates and accessories you need.
How much does DIY installation save?
Professional installation of an aluminum fence typically adds about $15 to $40 per foot, so doing it yourself saves that labor. See current material prices in our cost per foot guide.
Do I have to set the posts in concrete?
No. Posts can be set in concrete, surface mounted with base plates on a slab or footing, or attached directly to a wall.
Can I cut the slats to size?
Yes. Slats can be cut to fit narrower openings with a saw blade rated for aluminum, and posts can be trimmed for custom heights.
Get Everything You Need in One Order
Start with the fence calculator to see exactly which materials your project needs. We ship complete QuickScreen fence and gate systems nationwide, with the posts, frames, slats and hardware for your layout. Browse our aluminum fence and gate panels.
Request a quote, call (469) 817-3385 or email sales@foundationfencesupply.com.